The first thing I did was to completely strip the antennas off the mast that is bolted to the gable on the South end of the house. The 23cm 35 ele Tonna was finally replaced by an extended ‘M-Squared’ 35 ele (now 43 ele). The 13cm 25 ele came down on account that the accompanying transverter was just NOT working, and the old 18 ele parabeam shifted up in its place, just leaving room, albeit not optimum spacing, for my now un-bent 8 ele Eagle for 2m at the bottom. Also present on this little mast are a UHF dipole and a VHF dipole for 70cm and
During August 2003 I began to take stock of ‘things’. Now well into the ‘doldrums’ of H.F propagation, I began to look for other inspiration and decided to drastically change my antenna configuration. Something inside me simply cannot abide the sight of antennas lying unused, especially when I have the equipment that goes on the other end of the coax. And besides, the Mini-Quad was looking decidedly lonely.
As can be seen from the photo on the right, there have been a few additions to the shack. I was fortunate to get a good deal on a second-hand ICOM 706MK2 which prompted me to resurrect my 6m 3-ele beam.
The 706 uses ALC to control the output power in such a way that even when low power is selected, it will always initially output several milliseconds worth of full power. Because of this, I still use the IC260 to drive my 2m amplifier. It would have been convenient to use the 706 but I felt that with the MK2 capable of delivering 20W on 2m, it was simply not worth the risk of blowing the PA in the amplifier. Consequentially, the 2m output on the 706 is attached to the dipole on the gable end. The Trio TR-8400, on top of it is connected to the UHF dipole. Ideally this ‘wee’ radio would be used for connecting to the DX-Cluster, but since there ain’t such a thing here in central Scotland, it is used in conjunction with my VX-1 when doing antenna work. It is good to be able to speak to someone in the shack when making fine adjustments to antennas.
Three little boxes became four! (see left) I have always loathed having to climb onto the desk in order to lean over the back of the radios in order to change antennas. Now in possession of two competent H.F boxes, and with the 706 doing 6m too, it was time for some ingenuity! The box second from the bottom (left) controls yet another remote switch-box on the wall above and behind the radios. Although this time it is a bit more than just a routing box. The 725 and 706 connect in at the bottom. On top there are two outputs; one for 6m the other for H.F. Either the 706 can be selected and switched between H.F and 6m or the 725 can be chosen, in which case, H.F is the default. The inputs to the box are also R.F sensing so that when transmitting, the other input is automatically grounded, thus protecting the other transceiver. There is also a manual setting which automatically grounds the ‘unused’ input when the other one is selected. This remote routing box can be seen in the photograph above, just behind and to the right of the Revex power meter with the ‘speaker’ on top.
Finally, I have never been one to run from a challenge and after consigning the 13cm transverter to the ‘junk box’, I repented of my brash decision. I systematically tested all the active devices and came to the conclusion that the mixer was faulty and decided to replace it with a Mini-Circuits ADE-3G surface mount device. Fortunately only minor track changes were necessary, and the transverter burst into life and now delivers a good clean 1 Watt of power. With 13cm now a viable band, I needed a perch for the antenna. There were still two spare runs of 4-50 coax on the main mast and one of these was a single uninterrupted run of FSJ4-50B, all the way past the rotator and which had once fed my UHF colinear. Thus, the end-mounted 25 ele Tonna is now mounted on the main mast, half way between the 6m beam and the Mini-Quad. Now if I could just find someone to work on 13cm! . . . Hmmm?